How To Make DMT
DMT stands for N,N-dimethyltryptamine. It is a semisynthetic
compound similar to psilocin(the hallucinogenic substance in
psilocybin) ins
structure. The most common method of ingestion is
smoking. Soaked parsley leaves are the
usual method of ingestion
although persons have dipped marijuana in it and said the
experience was fantastic. The following recipe can be performed in
the kitchen.
Recipe for DMT:
1. Mix thoroughly and dissolve 25 grams of indole with a pound of
2. Take an ice tray and fill with
chipped or shaved ice. Cool
solution for about 35 minutes until it reaches 0 degrees C. At
the
same time cool 50 ml dry oxalychloride to about 5 degrees below 0
C. in the same
ice tray.
3. VERY slowly add the oxalychloride solution to the indole
solution.
These two chemicals are highly reactive. Avoid boiling
over, contact with skin, and fumes.
4. Wait until all the bubbling has died down, then add a few
handfuls of table
salt to the ice tray, to cool the solution
further. Label the solution "solution 1"
and put it in the
freezer.
5. Cool 100 ml. of dry ethyl ether in a 500 ml.
flask to 0 degrees
C. in a salted ice tray. At the same time cool an unopened bottle
of dimethylamine to 0 degrees C. in the same ice bath.
6. Open the seal of the
dimethylamine bottle and slowly pour a
steady stream into the ether. Label "solution
2."
7. Very slowly and carefully add solution "1" and "2"
together.
8. Now take the mixed solutions from the ice tray and bring up to
room temperature stirring the solution all the time. You should be
left with a solution that
is almost clear. If it is still murky,
continue stirring until it becomes as clear as
possible.
9. Now filter the solution to seperate the precipitate by suction.
<—Solution and Precipitate
————
\ /<—Funnel / / <– Rubber
hose to
\ / and / / Vacuum source
\ / Filter/____/
\*****\ /*************{
}*****/ <— Two hole
\****{ }*************{ }****/ rubber stopper
\ { } { }
<-/— Glass Tube
\ { } { } /
| { } { } |
| |
| |
| |
|
|
|__________________________|
Figure A.
10. Refilter with suction after
pouring technical ether over the
precipitate.
11. Repeat filtering once more
with ether, then twice with water.
12. Let this substance dry on a plastic or china
plate.(do not use
metal) After drying, a solid material will be formed. Take
particles
and place them in an 800 ml beaker.
13. Mix 100 ml. benzene with 100 ml. methyl
alcohol. After this
mixture has been stirred, cover solid particles from step 12 with
about 1/2 inch of the solution and heat the beaker in water until
all solid material had
dissolved. Add more solvent if
necessary.(Note: Do not place beaker in water bath directly
over
the flame.)
14. After all solid material has dissolved, remove beaker from
the
heat, and allow to cool. As it cools, small needle-shaped crystals
will appear.
When this happens, try to pour off as much solvent as
possible without disturbing the
crystals.
15. Place crystals in a 1000 ml flask and dissolve in
tetrahydrofurane.(Use only as much as absolutely necessary.) Label
this solution
"A".
16. Slowly mix 200 ml. tetrahydrofurane and 20 grams lithium
aluminum hydride in a 500 ml flask, and label it solution "B".
(By the way, lithuim
aluminum hydride ignites on contact with
moisture. Protect eyes and hands.)
17.
Mix solutions "A" and "B" slowly, stirring constantly.
18. Prepare
a water bath and heat solution for three hours,
stirring for four minutes every half hour.
When not stirring, make
sure to use aspirator tube.
/ / <— Rubber Tubing
—
\**{ }**/<—- One hole rubber stopper
/**{ }**\ and glass tubing
/ { }
\
/ { } \
: :
: :
: :
\ ~~~~~~~~~~~~~~~:_____________:~/
\______________________________/
Heat source
Figure B.
Place Figure B. flask at a higher level than Figure A. flask. Run
tube from Figure B. flask
down to left side of figure A. flask,
replacing funnel with glass tubing. Disconnect right
side tube
from vacuum source. This will be used as the aspirator tube.
19. When
this is completed, allow the flask to remain at room
temperature for about 20 minutes. Then
place in salted ice bath,
and cool to 0 degrees C. Add a small amount of chilled methanol,
stirring gently until solution appears murky.
20. Filter this murky solution
through a paper filter in a funnel,
and collect the filtered liquid in a flask.
21. Add 100 ml. of tetrahydrofuran through the filter and collect
in the same flask. Now heat
the solution in a water bath until
most of the tetrahydrofuran is evaporated and a gooey
substance
remains.
22. Place little piles of this substance on a cookie tray
and dry
with a heat lamp for three or four hours.
Well, after all that you now
have DMT. Was it worth it? To ingest,
crumble a small quantity with parsley or mint, and
smoke. Do not
inject. Do not mix with tobacco.
Keep your thoughts free
and your reality…err
different.
- Black Adder
Call
Spatula City (707) 451-2835.
Amiga 14.4 HST.
[0;1m
i heard of a relative to dmt called o-u-t that was much easier to make. it involved otc products and used o have a how-to vid on youtube but got deleted, and now i cant remember the recipe. can anyone help?
Add A Comment