Blowgun

Blowgun by The Jolly Roger

In this article I shall attempt to explain the use and manufacture
of a powerfull blow-gun and
making darts for the gun.The possesion of
the blow gun described in this article IS a
felony.
So be carefull where you use it. I don’t want to get you all busted.

Needed:

1. Several strands of yarn (About 2 inches a-piece)
2. A regular
pencil
3. A 2 1/4 inch long needle (hopefully with a beaded head. If not
obtainable,wrap
tape around end of needle.
4. 2-3 1/4 foot pipe. (PVC or Aluminum) Half a inch in diameter />
Constructing the dart:

1st- Carefully twist and pull the metal part (Along
with eraser)
of the pencil till it comes off.
2nd- Take Pin and start putting about 5-7
Strands of yarn on the pin. Then
push them up to the top of the pin. But not over the head of
the pin (orthe tape).
3rd- Push pin through the hollow part of the head where the pencil was
before.
4th- That should for a nice looking dart. (see illustration)

#####

>>>>>—–/ # is the yarn
> is the head of the pencil
- is the pin
it-self
/ is the head of the pin

Using the Darts:

1st- Now take the
finished dart and insert it in the tube
(if it is too small put on more yarn.)
2nd- Aim
the tube at a door, wall, sister, ect.
3rd- blow on the end of the pipe.
4th- Sometimes
the end of the pipe may be sharp. When this happens I
suggest you wrap it with some black
electrician tape.It should feel
a lot better.
-= RFLAGG =-



• Blowgun
• How To Make Blow Darts
• James Bond Pen
• So you want to become a Mercinary
• BUILDING ROCKET LAUNCHERS

Introduction:

In this article we will attemt to explain the use and manufacture of a
powerfull
blow-gun and making darts for the gun.

WARNING!!!!!!
————-
The
possestion of the blow gun described in this article IS a felony. So be
carefull where you use
it. I dont want to get you all busted.

Needed:

1. Several strands of yarn
(About 2 inches a piece)
2. A regular pencil
3. A 2 1/4 inch long needle (hopefully with
a beaded head. If
not obtainable wrap tape around end of needle.
4. 2-3 1/4 foot pipe.
(PVC or Aluminum) Half a inch in diameter

Part // : Constructing the dart.

——————————–

1st- Carefully twist and pull the metal part (Along
with eraser) of the pencil
till it comes off.

2nd- Take Pin and start putting
about 5-7 Strands of yarn on the pin. Then
push them up to the top of the pin. But not over
the head of the pin (or the
tape).

3rd- Push pin through the hollow part of the
head where the pen cil was
before.

4th- That should for a nice looking dart. (see
illustration)

####\
#####>>>>>—–
####/

/>
# is the yarn
> is the head of the pencil
- is the pin it-self

Part ///: Using the Darts
————————-

1st- Now take the finished
dart and insert it in the tube (if it is too small
put on more yarn.)

2nd- Aim
the tube at a door,wall,sister, ect.

3rd- blow on the end of the pipe.

4th- Sometimes the end of the pipe may be sharp. When this happens I suggest
you wrap it with
some black electrician tape. It should feel alot better.

• Blowgun
• How To Make Blow Darts
• James Bond Pen
• To make a still:
• So you want to become a Mercinary