Casings

[kbk]

Toilet paper tubes work quite well for most things. However sometimes you need something stronger so that it doesn't just blow apart when the initiating charge goes off...For this you could use a pill bottle or other plastic container. Something else would be to roll your own casings which is pretty easy and you can probably figure out how to do it yourself..

[-inefficiency-]

duct taped film canisters?
Small bottles or something similiar if you wanna do some damage with shards of glass.... I guess that would work.

[kbk]

The point of most casings I was talking about wouldn't be to do damage....PVC or a steel casing would work well for that though.

[blank stare]

A hollow pen. An empty chapstick.

[kbk]

I have heard of people using straws for blasting cap purposes...Also bottle caps.

[-inefficiency-]

I can't think of anything that small, I just keep thinking about cassete cases for some reason.
Smarties tubes? :P

[Douchermann]

What about those M&M minis cases, you know the ones im talking about that little kids are always walking around with them hangin out of their pockets.

[icecool]

Drinking straws, I always use them for blasting caps.

[Jago]

blasting caps, anything small and easy to work with.
As for main charge, it depends on the material. You can use plastic lunch boxes, or metal containers, or anything really. Just make sure it doesn't react with the explosive and noone is around to get hurt from the shrapnel

[Synchronium]

Glass ignition tubes.

Like a test tube but about 7cm tall and 0.5cm in diameter. Pack (and I mean, really pack) that with HMTD about 3/4 full. On top of that, add a layer of BP about 1cm thick just to ensure it'll work. Stick a length of fuse or ignition wires into the black powder and add a layer of poly cement to prevent BP falling out, especially if you'll be using these at an angle - BP coming loose will result in premature ignition in a fuse based cap, although not by much.

[Douchermann]

Yeah i've heard of those before, i'll have to try that. I use drinking straws too. I might start using refridgerator tube (copper pipe) after i do some tests on how much more sensitive something like AP is when it touches copper.

[Mumbles]

Refridgerator tubing is far too thick for caps. You want something with thin walls. They actually sell perfect sized tubing at most hardware stores. As for what it is used for I haven't a clue. I usually find it near the dowels, and steel rod. They are just these little tubes, probably 6" to 2' long, They are aproximatly 1/4" in diameter and have thin but decently strong walls. I believe they are made from brass instead of copper. They may bend or pinch off if you try to cut too hard. They are relativly easy to reopen though.

For most of my tubing needs I roll my own. I use cardstock material to build up the bulk of the tube, and 60# recycled kraft to smooth the outside and hold the tube together. I usually roll long tubes and cut to my needs. It speeds up the process rather than individually rolling them.

[Kaos-theory]

i find the tubes inbetween things like clingfilm and tin foil work well nice thick wals and about an inch round. i have a shit load stashed, because i cant be fucked to "blow shit up" any more

[Douchermann]

1 inch packing tubes, have unreasonably thick walls, (or so i've found). Thats what I made my 50, 80, 2x 100, and 2x 250gram flashpowder salutes. (don't tell me that im crazy or shit alrite? It will be my fault if I fuck myself up, and everyone else at that party coulda second'd that.

[Synchronium]

To be honest you'd be better off rationing that flash. 10g of flash is perfectly loud and bright. I doubt you'd notice much of a difference from say 100 to 250g of flash.

You're just squandering resources.

[darquedante]

You can allways try and roll your own tubes, I never realy put much effeor into it, you can allwasy find left over tubes at different stores, just tell themn you are using them for arts and crafts stuff

[ecko]

roll your own tubes, use a pliers and ppush the ends shut with hot glue. Then bend them back up to the tube and tape them there.

[Shalshaska]

I use rolled pieces of aluminum sheet from soda cans for blasting caps. Crimped with pliers.

[Jago]

Originally Posted by Shalshaska

I use rolled pieces of aluminum sheet from soda cans for blasting caps. Crimped with pliers.

Not the best idea if you are using peroxides in your blasting caps.

[pyromainiac420]

typically not but if you make the blasting cap right before detonation you should be fine but still....i wouldnt do it

[Shalshaska]

AP doesn't typically react with metals very much, at least not half as much as HMTD. But anyway, I forgot to mention that with the blasting caps I've made, I just use a lining of the really thin plastic sandwich baggies. I haven't really needed to make more than about three blasting caps since I've only made a couple charges of ANFO, and a KClO3/Petrolatum mixture. When I do order some more AN, I plan to use the little capsules that toys come in from the coin machines near supermarket entrances.

[Jago]

It still reacts with metal none the less, i wouldn't chance it. Be careful with the plastic too, acetone that's present may eat away at it (i can't remember if it does or doesn't, but just incase. But yea, i may be wrong).
The capsules are a good idea, you can use film canisters too, anything similar.
Coming to think of it, the AP SHOULDN'T eat away at it, just run a test next time you do it. The excess acetone (if any was present) should have evaporated off in the drying process and/or should have been washed off.

[headcase]

About the tin cans, wouldn't you also need to crimp it with the AP inside? That'll be a lot of (metallic) pressure you're putting the AP under if you screw it up. Too many risks, why bother?

[Shalshaska]

AP will go off with sudden pressure, like a hammer strike, but slow application from a vise or pliers (probably) won't set it off. Either way, the 'probably' is why I always used full face masks and heavy gloves. And I pretty much never touched the cap itself, it was held in a vise. But as I said, you guys are right about that being too risky, which is why I plan to use the capsules next time I need a blasting cap.

[pyromainiac420]

what forms of ANFO have you made?

[Shalshaska]

I've only made two charges, one that I used most of my AN with, using diesel. The other one, I wanted to see how plain gasoline compared with diesel, so I used some premium gas. I'm not even really sure I quite got a full det. from the gasoline one, which was sort of disappointing. With the big one, I put it inside a rusty car in the woods near a cemetery; stuck it to the roof in the car and blew a hole through

[pyromainiac420]

haha what did you use to detonate it? what i mean is like did you use a AP and APAN detnator or (ive only heard of this being used once) a co2 black powder bomb or what?

[ecko]

I use rolled pieces of aluminum sheet from soda cans for blasting caps. Crimped with pliers.

i made an egg on that on rotteneggs.com

its a good casing.

[pyromainiac420]

I use straws, they work fine.

[Kataklysm]

I use the launch tubes from Saturn missile batteries.