-- Posted by crookedromeoboom on 11:41 pm on Feb. 19, 2002 how would i make a home-made stun gun or a homemade tattoo gun????? -- Posted by Zambosan on 11:12 am on Feb. 20, 2002 I can only guess what these two have to do with each other... I suppose a combination of both would keep the tattoo-ee from squirming so much. :biggrin: -- Posted by Hergor on 11:17 am on Feb. 20, 2002 i think he wants a tatoo made of these black dots that form after direct skin contact with a tazer... :biggrin: "hey mom! look at my ass! i got a self-made non-permanent tatoo!" -- Posted by Switchy on 8:19 pm on Feb. 21, 2002 this isn't a tazer, but it'll give a little unexpected shock. get a grill starter at the hardware store and hook a couple wires up to it.  touch the wires to someone's skin and press the button on the grill starter and it'll make a little shock  (the grill starter is a little button thing that I guess makes a spark to start a grill.  I haven't made one but my friends did once and went around shocking everyone.  I didn't get a good look at how it was constructed but I think I got the gist of it.) -- Posted by Hergor on 8:56 am on Feb. 22, 2002 these grill lighter 'shockers' are called 'piezoelectric devices' and yeah they are fun. besides, you can make quite good impact primers out of them. just take two short wires and attach one to the inside of it (where the small hole is) and the other to the case (to the metal part, but do i need to tell?). then put some insulation tape between their deinsulated ends and tape them 'round, too. there you go... -- Posted by diggerdoo on 6:12 am on Feb. 27, 2002 I've made a stun gun out of an external camera flash (the kind that takes batteries and is remotely triggered).  **I'VE NEVER TESTED THIS ON ANOTHER PERSON**  When used, it welded the screwdriver to the two probes! First, you must remove the little strobe light from the flash; there should be three wires attached to it. The outer two wires get attached to two screws which you've added to the outside of the flash case (the probes) Now you charge the flash up like you were going to take a picture (you can hear the capacitor charging). Now touch the probes to a screwdriver and ZAP, instant weld. As the human body conducts electricity,  this could be a heart stopper. Sharpen your screws for maximum effect, minimizing (sp?) any chance that the probes will not reach the skin. -- Posted by ActionTimedDeath on 10:01 am on Feb. 28, 2002 I posted something like this in a thread a while ago - I played around with a small camera flash when I was 10 or so. An external high power bastard-strobe though?! I may have stuck myself to the wall using that one... (Thought: tonight, play with that club style huge strobe I've got sittin in that thar corner over there...) I think I'll start an electric shock story thread! -- Posted by youngnthugin212 on 9:32 pm on Mar. 2, 2002 I have made a few tattoo guns myself and even used them on myself they work!!! Just e mail me and i will explain!!!!!!!!!! :) -- Posted by Zero Dark on 2:37 pm on Mar. 3, 2002 if you want to give yourself a tattoo get a nedel and heat it up on a stove and  put it on your skin, it'll hurt like hell but it'll get the job done. -- Posted by bigboom on 1:25 am on Mar. 5, 2002 Quote: from Zero Dark on 2:37 am on Mar. 4, 2002 if you want to give yourself a tattoo get a nedel and heat it up on a stove and  put it on your skin, it'll hurt like hell but it'll get the job done. I do that with pipe bowls got halfe a one beneath 2 moles looks like a frowning smily guy -- Posted by youngnthugin212 on 10:08 pm on Mar. 5, 2002 Materials: black tape tooth brush pen remote control motor (RC cars are good ones) if not a tape player or any other small motor will work a/c adapter from a cd player or something a small plastic gear about a Cm wide guitar string, one of the thick ones and a empty one of those tubes that hold ink from a pen now on to the complicated shit, first you need to get all of the bristles off the toothbrush using a razor. Then heat up the top of the brush so you can bend it sort of like this  bear with me on the drawing-      HHHHH                                    HHHHH                                       HH                                       HH                                       HH                                       HH                                       HH                                       HH now take the pen totaly apart and tape the pen itself paralel to the brush. leave it about 1/2 inch bellow the bottom of it.take the motor and position it so the little thing that sticks out and spins is directly over the center of the hole.tape it real good so it dont move but make sure the thing can still spin. there should be two wires on the motor. wire them to the two wires on the adapter.it has to have one of those box things on the plug in part or ot will blow up.now that you have get a gear that fits snug on the little spin thing. take a needle and heat it red hot and put a wole about a 16th of and inch from the edge of the gear.take the guitar string and pull all of the wire that is wraped around it off.bend about a CM of it at a 90 angle.sharpen the tip real sharp with a dremel or something.get the empty tube and put the string through it(this is so the string wont bend when you are using it.put the string down through the pen and take the end that you bent and put it in the hole of the gear. now all you have to do is plug it in and dip it in ink and go to town. -- Posted by youngnthugin212 on 10:10 pm on Mar. 5, 2002 i fucked up the drawing on my last post                                     HHHHH               HHHHH                     HH                     HH                     HH                     HH -- Posted by Thanatos on 8:39 pm on Mar. 6, 2002 to make a homemade tazer take a disposable camera with flash (you can get one at a photo developer say it's for a 'science project' or somthing) and open it up find the capacitor and attach wires to the positive and negative  wires leading out of it and  run them out of the camera (leave a deacent ammount of wire  out side of the camera) charge the flash when you touck the two wires togeather they should spark now you can see what it will do to a person (two little burn scars) and a hell of a shock (330v) -- Posted by Pyroclasm on 7:20 pm on Mar. 7, 2002 lol i also posted a thing about makin a stun gun outta a disposable camera, lol we all found it out for ourselves, i shocked myself with it when i dropped it on my lap once, fuckin hurt lol -- Posted by mrjingles on 6:27 am on April 2, 2002 my friend made a tattoo gun outa and eletric hair clipper he took it apart and like welded or i dunno how but he stuck a pin to this metal thing that moved rapidly from  side to side , it worked but it wasnt that accurate and sometimes scrathched ur skin istead of just piercing it... -- Posted by thadon41 on 8:25 am on April 2, 2002 Dewd, if you thinking of a job in tatooing people, then BUY a tatoo pen. Noones gonna pay you for tattoos when your using some DIY contraption.lol.If its for your own fucked up use, then still buy one. Its ALOT more hygenic and does it properly. As for the tazer type thing, the Grill lighter and wire thing works. Its kewl but you couldnt put someone to the floor with it. But kewl for a laugh. A good way to wake your girlfriend up :P -- Posted by Ghost2000 on 2:59 pm on April 2, 2002 Yeah be careful with those homemade tat guns brother.They hurt like hell and you tend to bleed a lot.A friend of mine gave me a tat with one and what did i get for trying to be cheap????A fucked up dragon on my arm get a pro to do the job cause the shit don't wash off......ever!! -- Posted by alibaba on 2:37 am on April 3, 2002 dont you have $10-20 ...you can get a 100,000 volt stun gun off ebay for about that price.....its where i got mine.. -- Posted by thadon41 on 4:19 pm on April 3, 2002 Dude their only €46.00 BRAND NEW! from: http://www.guns2u.com/products/stun_guns/power_200.htm -- Posted by mrjingles on 6:14 am on April 4, 2002 yeah i know them home made tattoo guns are pretty shit and the tattos he people came off any way, he used ball point pen ink and it mustn hav gone it deep enough , after like a week or so they  just scabbed up then left a scar... -- Posted by NAILBUNNY on 4:02 pm on April 5, 2002 you can't use pen ink for tattoos, it will always scab and never stay in the skin.  maybe little pieces but other than that it'll just scar. try using "india ink", Higgins makes some good waterproof ink in all shades of color good for homemade tats.  just dip in with a needle, preferably sewing machine needles since they're slightly larger, and stab away.  it also might work better if you tape 3 or so needles together (for thicker lines and time saving).     http://www.bombshock.com